Skills and Trades

Replies / Views	Last post
Which type of sealer is to be used on non-machined surfaces? A) Anaerobic sealer B) RTV C) Either ... Started by LaDunn	1 Replies 74 Views	Jun 23, 2018 by cat123
Most late model vehicles will use ________ as an intake manifold gasket. A) RTV B) Plastic/rubber ... Started by tsand2	1 Replies 713 Views	Jun 23, 2018 by joshraies
Which of these are attached to the rod journals on V-type engines to simulate the weight of the rods ... Started by debasdf	1 Replies 61 Views	Jun 23, 2018 by scikid
Why is it recommended that a new camshaft be degreed? A) Because of camshaft grinding variations ... Started by nmorano1	1 Replies 75 Views	Jun 23, 2018 by honnalora
Technician A says that material is drilled out of the counterweight to balance a crankshaft. ... Started by 809779	1 Replies 150 Views	Jun 23, 2018 by scikid
When balancing a 4-cylinder engine, all of the following parts are needed, EXCEPT ________. A) ... Started by Deast7027	1 Replies 84 Views	Jun 23, 2018 by krakiolit
A coating often used to keep an engine from rusting during assembly is called ________. A) ... Started by Davideckstein7	1 Replies 63 Views	Jun 23, 2018 by rekilledagain
When the pushrod is the correct length, the rocker arm tip will contact the ________ of the valve ... Started by Jkov05	3 Replies 43 Views	Jun 23, 2018 by lcapri7
An engine dynamometer measures ________. A) Torque B) Horsepower C) Both horsepower and torque ... Started by Jkov05	1 Replies 111 Views	Jun 23, 2018 by bigsis44
Two technicians are discussing the torquing process of head bolts. Technician A says that they ... Started by azncindy619	1 Replies 97 Views	Jun 23, 2018 by s.meritte
Technician A says that all oil galleries must be thoroughly cleaned before engine assembly can ... Started by rosent76	1 Replies 77 Views	Jun 23, 2018 by Chou
Technician A says that the back of all engine bearings should be lubricated during assembly. ... Started by aabwk4	1 Replies 110 Views	Jun 23, 2018 by alexanderhamilton
Technician A says that the cam bearings should be installed using a driver and dead blow hammer. ... Started by Beheh	1 Replies 55 Views	Jun 23, 2018 by voltaire123
Dressing the engine means ________. A) Cleaning the engine B) Changing the oil and filter C) ... Started by piesebel	1 Replies 137 Views	Jun 23, 2018 by at
An engine dynamometer may use devices to convert pressure and temperature measurements into ... Started by joe	1 Replies 430 Views	Jun 23, 2018 by AaaA
How should the vehicle be driven to best break in a newly overhauled engine? A) At high speeds ... Started by jessicacav	3 Replies 39 Views	Jun 23, 2018 by ergserg
Technician A says to always adjust the clutch free play after starting the engine. Technician B says ... Started by BRWH	1 Replies 119 Views	Jun 23, 2018 by quynhmickitran
After rebuilding an engine, you need to have which of these near when the engine is first started? ... Started by sc00by25	1 Replies 32 Views	Jun 23, 2018 by taylorsonier
Most secondary fuel filters should not be prefilled before installation because: a. this will ... Started by azncindy619	1 Replies 21 Views	Jun 23, 2018 by kaillie
This would NOT be a normal part of PPE that a HDET would use: a. a cooling vest for extremely hot ... Started by ashley	1 Replies 30 Views	Jun 23, 2018 by apple
Brake tubing must be ________. A) Made of copper B) Single-walled C) Double-walled D) Able to ... Started by gonzo233	1 Replies 42 Views	Jun 23, 2018 by SomethingSomething
An HDET would NOT normally be required to do this: a. track the operating expenses for a machine ... Started by ahriuashd	1 Replies 37 Views	Jun 23, 2018 by sarah_brady415
Technician A says that disc brake pads should be replaced when worn to minimal allowable thickness. ... Started by justinmsk	1 Replies 163 Views	Jun 23, 2018 by essyface1
The caliper dust boot may need to be pried out with a(an) ________. A) Air chisel B) C-clamp C) ... Started by geoffrey	3 Replies 44 Views	Jun 23, 2018 by AngeliqueG
Which one of the following actions would NOT be normally taken when installing a threaded fastener: ... Started by DyllonKazuo	1 Replies 26 Views	Jun 23, 2018 by ryrychapman11