Skills and Trades

Replies / Views	Last post
Which of the following could be an acceptable feed for a 1/2 (.500 ) inch diameter drill in low ... Started by Alainaaa8	1 Replies 47 Views	Jul 26, 2018 by olivia_paige29
Express the tolerance +/- .05 mm. to the nearest thousandth of an inch. A) +/- .005 in. B) +/- ... Started by formula1	3 Replies 17 Views	Jul 26, 2018 by dyrone
A wiggler is a: A) Spring loaded, scribe like indicator that can be trued to center by pushing on ... Started by serike	1 Replies 21 Views	Jul 26, 2018 by choc0chan
Spotfacing is done with a: A) Countersink B) Counterbore C) Spotting drill D) ... Started by maegan_martin	1 Replies 24 Views	Jul 26, 2018 by ghepp
The included angle of a center drill is ________ degrees. A) 90 B) 30 C) 60 D) ... Started by appyboo	1 Replies 24 Views	Jul 26, 2018 by mbcrismon
The discrimination of a typical dial caliper is 0.010. Indicate whether the statement is true or ... Started by sammy	3 Replies 15 Views	Jul 26, 2018 by ngr69
Compared with the feed rate for drilling the same material, the feed rate for reaming is ________ ... Started by robinn137	1 Replies 88 Views	Jul 26, 2018 by alexisweber49
Calibration is the process by which any measuring instrument is compared with a known standard. ... Started by gonzo233	1 Replies 79 Views	Jul 26, 2018 by Expo
Coolant is used while reaming to: A) Cool the tool B) Improve surface finish C) Wash away chips ... Started by Cooldude101	1 Replies 64 Views	Jul 26, 2018 by dreamfighter72
In order to be certain of the dimension when measuring with a micrometer: A) Take at least one ... Started by jace	3 Replies 19 Views	Jul 26, 2018 by Laurenleakan
The lathe carriage is made up of the saddle and apron. Indicate whether the statement is true or ... Started by Mimi	1 Replies 12 Views	Jul 26, 2018 by wergv
The part of the micrometer which supports the anvil is called the: A) Brace B) Frame C) Support ... Started by vicky	1 Replies 54 Views	Jul 26, 2018 by Mochi
Express the tolerance +/- .125 inch in terms of mm. to the nearest 1/100 mm. A) +/- .05 mm. B) ... Started by lracut11	1 Replies 17 Views	Jul 26, 2018 by yuyiding
An angular, odd shaped workpiece cannot be mounted satisfactorily on the drill table or in a vise. ... Started by nramada	3 Replies 35 Views	Jul 26, 2018 by sarajane1989
Straight shank tools are held in the a tailstock with: A) Set screws B) A drill chuck C) A taper ... Started by cool	1 Replies 29 Views	Jul 26, 2018 by bbburns21
It is sometimes a good idea to start a tap with a drill press since: A) If you get tired turning ... Started by armygirl	1 Replies 17 Views	Jul 26, 2018 by efwsefaw
Back and side rakes: A) Are both the same with different names B) Provide adequate clearance ... Started by RRMR	1 Replies 14 Views	Jul 26, 2018 by aburgess
If you add the angles in any triangle they will total 180 degrees. Indicate whether the statement ... Started by nmorano1	3 Replies 157 Views	Jul 26, 2018 by upturnedfurball
Datums are reference points, lines, areas, and planes taken to be exact for the purpose of ... Started by strangeaffliction	1 Replies 12 Views	Jul 26, 2018 by bobsmith
What are face plates used for? A) Facing operations only B) Mounting fixtures and workpieces C) ... Started by bcretired	1 Replies 36 Views	Jul 26, 2018 by aliotak
What numerical system is used to designate carbon in alloy steels? A) U.S.A. B) SAE - ANSI C) ... Started by maegan_martin	1 Replies 37 Views	Jul 26, 2018 by momolu
Color coding is used as one means of identifying a particular type of steel. Its main disadvantage ... Started by cartlidgeashley	3 Replies 21 Views	Jul 26, 2018 by Ashley I
What effect do you think the carriage feed/cross feed ratio would have on surface finish if the same ... Started by ashley	1 Replies 37 Views	Jul 26, 2018 by nickk12214
The element chromium (Cr) is what makes stainless steels stainless. Indicate whether the ... Started by formula1	1 Replies 79 Views	Jul 26, 2018 by Bison
Austenitic steels are always: A) Non-magnetic when annealed B) Weaker than ferritic steels C) ... Started by ahriuashd	1 Replies 43 Views	Jul 26, 2018 by lou