Skills and Trades

Replies / Views	Last post
A lathe that is calibrated for single depth: A) Will take twice the amount turned on the dial ... Started by TFauchery	3 Replies 43 Views	Jul 26, 2018 by Galvarado142
Center drills break as a result of: A) Too heavy feed and too low speed B) Dropping them on the ... Started by khang	1 Replies 33 Views	Jul 26, 2018 by johnpizzaz
The feed change lever: A) Changes the feed to a high or low range B) Changes the direction of ... Started by lb_gilbert	1 Replies 19 Views	Jul 26, 2018 by duke02
The sliding gear shifter levers on the quick change gear box are used for: A) Selecting feeds or ... Started by luvbio	1 Replies 15 Views	Jul 26, 2018 by yeungji
The severity of water quench sometimes causes: A) One inch thick sections to harden clear through ... Started by jake	3 Replies 34 Views	Jul 26, 2018 by tkempin
A 1040 steel would have 10 points of carbon. Indicate whether the statement is true or ... Started by karen	1 Replies 16 Views	Jul 26, 2018 by nguyenhoanhat
Furnaces used for heat treating steels are: A) Electric, gas B) Open hearth, Bessemer C) ... Started by FButt	1 Replies 52 Views	Jul 26, 2018 by tennis14576
Agitating the part in the quenching medium: A) Breaks down the vapor barrier for more rapid ... Started by fbq8i	1 Replies 13 Views	Jul 26, 2018 by livaneabi
Taps used for lathe tapping are: A) Spiral, plug and taper B) National fine, National coarse and ... Started by asan beg	3 Replies 47 Views	Jul 26, 2018 by Ptupou85
When grinding hardened steel, two kinds of surface failures are: A) Decarburization and pitting ... Started by justinmsk	1 Replies 27 Views	Jul 26, 2018 by Qarqy
The normalizing temperature is: A) 500 F. (100 C.) above the upper critical T line (in steels ... Started by dmcintosh	1 Replies 59 Views	Jul 26, 2018 by smrerig
The stress relief temperature is: A) 950 F. (570 C.) to 1250 F. (677 C.) B) 1000 F. (380 C.) ... Started by londonang	1 Replies 13 Views	Jul 26, 2018 by qytan
The percent of thread: A) Indicates the depth of the external thread expressed as a percentage ... Started by Yi-Chen	3 Replies 68 Views	Jul 26, 2018 by itsakadoozi
One reason for having thread tolerances and classes of fits is: A) So specific threads can be ... Started by arivle123	1 Replies 14 Views	Jul 26, 2018 by cdmart10
The number of threads per inch can be checked with a: A) Tool gage B) Ring gage C) Metric rule ... Started by soccerdreamer_17	1 Replies 38 Views	Jul 26, 2018 by brbarasa
For threading, the spindle should be turning: A) At about one-fourth normal turning speeds B) At ... Started by s.tung	1 Replies 25 Views	Jul 26, 2018 by cdmart10
Internal threads that are cut with a single point tool should have a bore size equal to: A) D = ... Started by anjilletteb	3 Replies 24 Views	Jul 26, 2018 by BAOCHAU2803
The percent of thread of the internal thread is affected by: A) Making taps for certain classes ... Started by audie	1 Replies 51 Views	Jul 26, 2018 by sabina576
For cutting internal right hand threads, the compound rest should be swiveled to: A) The right 60 ... Started by ereecah	1 Replies 23 Views	Jul 26, 2018 by covalentbond
Layout lines scribed with a height gage should be: A) Scribed so that a permanent mark is left on ... Started by fagboi	1 Replies 74 Views	Jul 26, 2018 by kescobar@64
After heating to full the full annealing temperature, how should the piece be cooled? A) By ... Started by pragya sharda	3 Replies 49 Views	Jul 26, 2018 by ecabral0
Threading tools are checked for accuracy on the 60-degree angle by using a: A) Tool angle gage B) ... Started by bucstennis@aim.com	1 Replies 81 Views	Jul 26, 2018 by strudel15
The tool is aligned with the work: A) With a small square B) With a center gage C) With a ... Started by genevieve1028	1 Replies 41 Views	Jul 26, 2018 by billybob123
When a shaft has centers, the steady rest is set up: A) With the shaft between centers, the top ... Started by rosent76	1 Replies 97 Views	Jul 26, 2018 by lindahyatt42
On the Brinell tester, how much load should be used for testing steel? A) 10 kg. B) 3000 kg. C) ... Started by jasdeep_brar	3 Replies 29 Views	Jul 26, 2018 by lcapri7