Skills and Trades

Replies / Views	Last post
When threading, the carriage is moved along the ways by: A) The lead screw B) The feed rod spine ... Started by j.rubin	1 Replies 181 Views	Jul 26, 2018 by stallen
The depth of thread in inches for a 1-1/2 - 5 general purpose Acme thread is: A) .120 in. B) .220 ... Started by RYAN BANYAN	1 Replies 36 Views	Jul 26, 2018 by yasmina
How can tapers be turned on a lathe? A) By the off hand method, the taper slide method and the ... Started by dbose	1 Replies 28 Views	Jul 26, 2018 by Alyson.hiatt@yahoo.com
Buttress threads are used: A) On special bolts used for the construction of dams and large ... Started by ericka1	3 Replies 23 Views	Jul 26, 2018 by Ahnyah
The Acme threading tool forms an included angle of ________ degrees? A) 55 B) 30 C) 29 D) ... Started by geoffrey	1 Replies 22 Views	Jul 26, 2018 by Edwyer
Which is the correct depth bore size in inches for an internal general purpose 2-1/2 - 3 Acme ... Started by KWilfred	1 Replies 34 Views	Jul 26, 2018 by sierramartinez
The fit is checked on an internal Acme thread with: A) A screw pitch gage B) A bore gage C) An ... Started by eruditmonkey@yahoo.com	1 Replies 33 Views	Jul 26, 2018 by EAN94
Threads are cut or chased on the lathe with a single point tool by: A) Moving the carriage by ... Started by serike	3 Replies 21 Views	Jul 26, 2018 by morrie123456
Sixty degree thread cutting is best done with the compound set at 29 degrees because: A) It ... Started by bobypop	1 Replies 53 Views	Jul 26, 2018 by Edwyer
What is the flat dimension in inches for a 10 thread per inch unified form thread if the formula is ... Started by newbem	1 Replies 35 Views	Jul 26, 2018 by potomatos
The sharp v thread: A) Has an included angle of 55 degrees B) Is very durable and will take much ... Started by javeds	1 Replies 64 Views	Jul 26, 2018 by Zack0mack0101@yahoo.com
Parting tools can jam in the cut and break as a result of: A) Cutting speed that is too high B) ... Started by Frost2351	3 Replies 83 Views	Jul 26, 2018 by TDubDCFL
Three reasons knurling is done on workpieces are: A) To cover up errors be increasing the ... Started by jCorn1234	1 Replies 26 Views	Jul 26, 2018 by JYan
Decarburization can be avoided in a furnace by: A) Using an electric furnace B) Laying the part ... Started by jho37	1 Replies 36 Views	Jul 26, 2018 by Galvarado142
Stub Acme threads are used: A) Where more strength is needed B) For short length screws C) On ... Started by theo	1 Replies 17 Views	Jul 26, 2018 by soda0602
The Acme tool is aligned to the work with: A) The eye B) A center gage C) A square D) The Acme ... Started by Pineapplelove6	3 Replies 72 Views	Jul 26, 2018 by meltdown117
In what position is the compound normally set for cutting right hand external Acme threads? A) 29 ... Started by darbym82	1 Replies 102 Views	Jul 26, 2018 by kaykay69
How many degrees is the included angle of general purpose Acme threads? A) 10 B) 60 C) 29 D) ... Started by sam.t96	1 Replies 27 Views	Jul 26, 2018 by mfedorka
You can set up a steady rest when the shaft has no center by: A) Holding the workpiece in a three ... Started by fnuegbu	1 Replies 47 Views	Jul 26, 2018 by jjorrostieta
Which is the most commonly used and easiest to machine of the translating type threads? A) Square ... Started by Sportsfan2111	3 Replies 14 Views	Jul 26, 2018 by dyrone
A finished tapered workpiece has an included angle of 70 degrees. If the taper is made with the ... Started by altibaby	1 Replies 34 Views	Jul 26, 2018 by ndhahbi
A steady rest should be used to: A) Support workpieces that extend three diameters from the chuck ... Started by bobbie	1 Replies 23 Views	Jul 26, 2018 by nital
Low carbon steels that are spheroidized tend to be: A) More likely to produce good finishes B) ... Started by aabwk4	1 Replies 29 Views	Jul 26, 2018 by flannelavenger
What is the correct procedure for using the steady rest when the workpiece is rough? A) Turn a ... Started by Capo	3 Replies 30 Views	Jul 26, 2018 by meganmoser117
Left-hand threads are cut by: A) Using a standard tool and setting the compound 29.5 degrees to ... Started by fahad	1 Replies 27 Views	Jul 26, 2018 by Carissamariew