Skills and Trades

Replies / Views	Last post
Five thread forms used on translating screws are: A) Buttress, modified square, square, Acme, and ... Started by KWilfred	1 Replies 19 Views	Jul 26, 2018 by alvinum
The thread is picked up when a threading tool is removed for grinding by: A) Replacing the tool ... Started by chads108	1 Replies 79 Views	Jul 26, 2018 by InfiniteSteez
The Brinell hardness test is performed by applying two loads to a specimen and measuring the depth ... Started by Engineer	3 Replies 63 Views	Jul 26, 2018 by mcni194
Commercial internal threads are typically cut at ________ of full depth A) 60 B) 70 C) 75 D) ... Started by panfilo	1 Replies 26 Views	Jul 26, 2018 by SomethingSomething
Large internal threads are often made on the lathe with single point tools because: A) Cleaner, ... Started by jerry coleman	1 Replies 14 Views	Jul 26, 2018 by katara
An 80 percent depth 3/8-16 UNC thread tap drill size is specified. Which of the following is ... Started by mp14	1 Replies 32 Views	Jul 26, 2018 by wilsonbho
Deflection of the boring bar causes: A) A tapered thread B) An oversized thread C) Chatter or a ... Started by Chelseaamend	3 Replies 43 Views	Jul 26, 2018 by jordangronback
On a 50 division inch vernier height gage, the vernier index is coincident at the 23rd line. This ... Started by sammy	1 Replies 72 Views	Jul 26, 2018 by hollysheppard095
What other names are used for slight tapers and for steep tapers when they are used for machining ... Started by tfester	1 Replies 62 Views	Jul 26, 2018 by orangecrush
When scribing perpendicular lines, the workpiece must be: A) Inverted B) Set on a parallel bar ... Started by fasfsadfdsfa	1 Replies 27 Views	Jul 26, 2018 by coyin
How can the tailstock be measured for offset? A) With a special gaging fixture B) By using a ... Started by MirandaLo	3 Replies 15 Views	Jul 26, 2018 by Jody Vaughn
On a 25 division inch vernier height gage, the vernier is coincident at the 17th line. If the beam ... Started by maegan_martin	1 Replies 75 Views	Jul 26, 2018 by Bison
After hardening, tempering should be done: A) Whenever time permits B) Within 24 hours C) ... Started by itsmyluck	1 Replies 10 Views	Jul 26, 2018 by briseldagonzales
Angle drilling is done by: A) A tilting type table or angular vise B) An angle drill press C) An ... Started by joblessjake	1 Replies 32 Views	Jul 26, 2018 by nanny
The finest discrimination on a typical fractional rule is usually: A) 1/32 inch B) 1/100 inch C) ... Started by khang	3 Replies 18 Views	Jul 26, 2018 by apple
A cylindrical square is used to measure: A) The squareness of a part placed on a surface plate ... Started by Caiter2013	1 Replies 29 Views	Jul 26, 2018 by aadams68
Assuming a dial indicator misalignment of 10 degrees from the axis of measurement, the cosine error ... Started by B	1 Replies 63 Views	Jul 26, 2018 by k2629
An AA set of gage blocks has a size tolerance of +/- .000002 inch. This set is: A) A laboratory ... Started by rosent76	1 Replies 37 Views	Jul 26, 2018 by strudel15
Which of the following are all workholding devices? A) Strap clamps, angular vises, C-clamps, v ... Started by Starlight	3 Replies 70 Views	Jul 26, 2018 by scikid
Parallels are used for: A) Aligning a center punch mark on round stock in vee-blocks B) Scribing ... Started by theo	1 Replies 53 Views	Jul 26, 2018 by chereeb
When a long workpiece is supported so it can spring down from the drilling pressure, what can be the ... Started by Jramos095	1 Replies 27 Views	Jul 26, 2018 by janeli1
The finest discrimination on a typical rule is 1/32 inch. Indicate whether the statement is true ... Started by jCorn1234	1 Replies 18 Views	Jul 26, 2018 by Sarahjh
The cutting speed used with a counterbore when compared with an equal size twist drill is: A) The ... Started by Brittanyd9008	3 Replies 24 Views	Jul 26, 2018 by momolu
A conditioning stone is: A) A fine abrasive B) Used a s a gage block heat sink C) Used sparingly ... Started by Pineappleeh	1 Replies 26 Views	Jul 26, 2018 by orangecrush
Decimal rules use the metric system of measurement. Indicate whether the statement is true or ... Started by washai	1 Replies 37 Views	Jul 26, 2018 by sultansheikh