Skills and Trades

Replies / Views	Last post
Grinding wheels on a pedestal grinder are usually sharpened and dressed with a: A) Crush roll B) ... Started by big1devin	1 Replies 18 Views	Jul 26, 2018 by Mollythedog
On a pedestal grinder, the left side of the spindle has left-handed threads, and the right side has ... Started by dejastew	1 Replies 61 Views	Jul 26, 2018 by Meganchabluk
A ________ must be installed between the wheel and flanges on each side of the wheel. A) spacer ... Started by urbanoutfitters	3 Replies 77 Views	Jul 26, 2018 by diesoon
Assuming that a drill press operator has selected the proper tool, assured his own safety and ... Started by charchew	1 Replies 25 Views	Jul 26, 2018 by kxciann
2.77 cm. is equal to: A) .1074 inches B) 107.4 inches C) 1.0704 inches D) .01074 ... Started by swpotter12	1 Replies 79 Views	Jul 26, 2018 by aham8f
Re-threading dies are used to: A) Cut occasional new threads B) Re-cut rusty or damaged threads ... Started by chandani	1 Replies 19 Views	Jul 26, 2018 by ASDFGJLO
A spade drill is a flat blade with sharpened cutting edges. Indicate whether the statement is ... Started by storky111	3 Replies 63 Views	Jul 26, 2018 by cdmart10
Spotting drills are used to position holes accurately for further drilling with regular drills. ... Started by leo leo	1 Replies 67 Views	Jul 26, 2018 by raenoj
The lead of a screw is: A) A lead bolt B) Part of an engine lathe C) The chamfer on the end of ... Started by D2AR0N	1 Replies 35 Views	Jul 26, 2018 by polinasid
Adjustable two piece dies are assembled: A) Without the guide B) With the chamfer away from the ... Started by mspears3	1 Replies 31 Views	Jul 26, 2018 by Mollythedog
When drilling soft materials, a drill point angle of between 60 and 90 degrees would work best. ... Started by anshika	3 Replies 43 Views	Jul 26, 2018 by recede
For heavy stock removal a ________ drill should be used. A) Jobber B) step drill C) core D) ... Started by CORALGRILL2014	1 Replies 38 Views	Jul 26, 2018 by wtf444
A round split adjustable die is expanded and contracted by: A) Nut B) Die adjuster C) Screw D) ... Started by Awilson837	1 Replies 12 Views	Jul 26, 2018 by leahm14
A die is turned with a: A) Die wrench B) Die plate C) Die stock D) Die ... Started by ETearle	1 Replies 11 Views	Jul 26, 2018 by Jevvish
The process by which the band weld is softened to improve strength qualities is: A) Softening B) ... Started by ssal	3 Replies 14 Views	Jul 26, 2018 by Ashley I
The upper guide post should be adjusted so that: A) One inch clearance exists between the band ... Started by iveyjurea	1 Replies 11 Views	Jul 26, 2018 by zacnyjessica
What type of tap should be used to push the chips ahead of the tap? A) Gun B) Bottoming C) Thru ... Started by dollx	1 Replies 8 Views	Jul 26, 2018 by gcook
The length (depth) of a tapped hole should be how many times the diameter of the screw? A) ... Started by james0929	1 Replies 30 Views	Jul 26, 2018 by iman
Shifting from high to low speed range: A) Must be done as quickly as possible so as not to grind ... Started by Garrulous	3 Replies 16 Views	Jul 26, 2018 by morrie123456
Taps may break when tapping: A) If the chips clog the flutes B) If the holes are drilled too deep ... Started by c0205847	1 Replies 26 Views	Jul 26, 2018 by Bison
Dull taps: A) Produced polished threads B) Produce oversized threads C) Should be honed more ... Started by xclash	1 Replies 64 Views	Jul 26, 2018 by hanadaa
Tap drill sizes are based upon the drill diameter being ________ of the thread size. A) 75 B) 90 ... Started by lidoalex	1 Replies 68 Views	Jul 26, 2018 by tmlewis4706
Taps are surface treated to: A) Be used on automatic machines B) Keep them from corroding C) ... Started by Kikoku	3 Replies 28 Views	Jul 26, 2018 by iman
The difference between the taps in a standard (not serial) set is found on the: A) Pitch diameter ... Started by misspop	1 Replies 33 Views	Jul 26, 2018 by aham8f
A hand reamer should be turned with an adjustable wrench. Indicate whether the statement is true ... Started by fasfsadfdsfa	1 Replies 11 Views	Jul 26, 2018 by Gabe