Skills and Trades

Replies / Views	Last post
The saddle supports: A) The table B) The column C) The knee D) None of the ... Started by FButt	1 Replies 36 Views	Jul 26, 2018 by kusterl
Which type of end mill would you use to remove a considerable amount of material? A) Regular ... Started by mckennatimberlake	1 Replies 44 Views	Jul 26, 2018 by yasmina
Milling cutters with carbide inserts are used to: A) Remove material efficiently B) Machine most ... Started by jace	1 Replies 42 Views	Jul 26, 2018 by Athena23
Dovetails are milled with: A) Double angle milling cutters B) Dovetail cutters C) Single angle ... Started by chads108	3 Replies 107 Views	Jul 26, 2018 by Eunice618
When an edge finder is used to align the spindle center line with a workpiece edge, the spindle RPM ... Started by james	1 Replies 53 Views	Jul 26, 2018 by ntsoane kedibone
While aligning a workhead, the head clamping bolts should be: A) Removed B) Loose C) Tight D) ... Started by cherise1989	1 Replies 69 Views	Jul 26, 2018 by shoemake
High cutting speeds are used with: A) Light cuts B) Heavy cuts C) Large diameter cutters D) All ... Started by Evvie72	1 Replies 85 Views	Jul 26, 2018 by olivia_paige29
On a setup that is not very rigid, use a: A) Heavy feed B) Higher cutting speed C) Larger ... Started by littleanan	3 Replies 150 Views	Jul 26, 2018 by choc0chan
Cutting fluids: A) Act as lubricants B) Prolong tool life C) Increase production D) All of the ... Started by FButt	1 Replies 35 Views	Jul 26, 2018 by ngr69
The effects of an excessive feed rate are: A) Cutting edge chipping and possible broken cutters ... Started by asmith134	1 Replies 13 Views	Jul 26, 2018 by fraziera112
The longest tool life can be obtained when using: A) The correct coolant B) The right cutting ... Started by colton	1 Replies 50 Views	Jul 26, 2018 by Swizqar
A right angle milling attachment: A) Is used in hard to reach places on a workpiece B) Makes ... Started by sabina	3 Replies 17 Views	Jul 26, 2018 by mmpiza
What is the RPM for a 1/4 (.250 ) inch diameter, four flute end mill at a cutting seed of 200 SFPM? ... Started by Lisaclaire	1 Replies 78 Views	Jul 26, 2018 by aliotak
Vibrations in a boring operation can be: A) Stopped by increasing the feed rate B) Caused by an ... Started by sjones	1 Replies 39 Views	Jul 26, 2018 by momolu
The hole size obtained by boring is affected by: A) The material being machined B) The depth of ... Started by WhattoUnderstand	1 Replies 28 Views	Jul 26, 2018 by aadams68
A precise square on the end of a shaft is best machined: A) With a dividing head B) With a ... Started by Sufayan.ah	3 Replies 55 Views	Jul 26, 2018 by mfedorka
The difference between a plain milling machine and a universal milling machine is that the universal ... Started by stephzh	1 Replies 55 Views	Jul 26, 2018 by polinasid
When milling a keyseat into a shaft: A) The cutter needs to be centered over the shaft B) The ... Started by Sportsfan2111	1 Replies 55 Views	Jul 26, 2018 by amcvicar
The purpose of the overarm is: A) Extend the spindle B) To hold large face mills C) To hold the ... Started by plus1	1 Replies 58 Views	Jul 26, 2018 by ashely1112
The saddle moves when operating the: A) Vertical feed B) Length feed C) Cross feed D) None of the ... Started by bobbie	3 Replies 88 Views	Jul 26, 2018 by Ptupou85
The arbor is driven by: A) The keys in the spindle nose B) The friction between the tapers C) ... Started by Shelles	1 Replies 29 Views	Jul 26, 2018 by pami445
Table and saddle micrometer collars are graduated in increments of ________ inch. A) .005 B) .001 ... Started by bcretired	1 Replies 76 Views	Jul 26, 2018 by gcook
Helical milling cutters: A) Chatter easily B) Cannot be re-sharpened C) Leave rough surfaces D) ... Started by Garrulous	1 Replies 47 Views	Jul 26, 2018 by chevyboi1976
Angular milling cutters are used: A) To mill dovetails B) To mill vee-notches C) To chamfer ... Started by cdr_15	3 Replies 109 Views	Jul 26, 2018 by Kedrick2014
Half side milling cutters are used to: A) Mill shallow grooves B) Straddle mill C) Mill deep ... Started by jwb375	1 Replies 127 Views	Jul 26, 2018 by jesse.fleming