Skills and Trades

Replies / Views	Last post
A rough casting can be securely held for machining: A) In an all-steel vise B) By clamping it to ... Started by nevelica	1 Replies 46 Views	Jul 26, 2018 by Eunice618
Before placing rough castings on a machine table: A) Place a shim on the table B) Align the screw ... Started by cherise1989	1 Replies 66 Views	Jul 26, 2018 by cpetit11
Direct indexing is performed: A) On the spindle nose B) Through the gear train C) On the side ... Started by Bernana	3 Replies 26 Views	Jul 26, 2018 by Alyson.hiatt@yahoo.com
The sector arms are used: A) To divide a circle evenly B) On the side index plate C) When direct ... Started by cartlidgeashley	1 Replies 42 Views	Jul 26, 2018 by yasmina
On a dividing head with a 40:1 ratio, one turn of the index crank revolves the spindle ________ ... Started by sammy	1 Replies 66 Views	Jul 26, 2018 by vish98
How many turns of the index crank are required to index 63 degrees? A) 12 turns B) 4 turns C) 7 ... Started by nmorano1	1 Replies 88 Views	Jul 26, 2018 by Ashley I
How many turns of the index crank are needed to index 19 degrees? A) 2-1/9 turns B) 4-1/9 turns ... Started by 809779	3 Replies 69 Views	Jul 26, 2018 by akpaschal
Cutting speed is expressed as: A) Surface feet per minute B) Inches per minute C) Surface feet ... Started by 123654777	1 Replies 58 Views	Jul 26, 2018 by ky860224
When starting a cut, it is best to: A) Use the calculated feed rate B) Increase the feed rate at ... Started by jazziefee	1 Replies 38 Views	Jul 26, 2018 by sabina576
The depth of cut for a finish cut should be approximately ________ of an inch? A) .005 B) .020 C) ... Started by abc	1 Replies 63 Views	Jul 26, 2018 by ryhom
When climb milling, the force of the cutter: A) Pushes the workpiece away from the cutter B) ... Started by Beheh	3 Replies 49 Views	Jul 26, 2018 by zoeyesther
What is a more accurate tool for aligning a vise? A) Dial indicator B) Precision square C) ... Started by bclement10	1 Replies 27 Views	Jul 26, 2018 by sierrahalpin
In gang milling, the depth of of the individual steps is controlled by: A) The diameter of the ... Started by Capo	1 Replies 19 Views	Jul 26, 2018 by bhavsar
Layout lines on a workpiece: A) Should be accurate B) Identify where machining is to take place ... Started by cool	1 Replies 19 Views	Jul 26, 2018 by katkat_flores
Heavy duty face mills: A) Have many teeth B) Have few teeth C) Are used for finish cuts D) None ... Started by fahad	3 Replies 17 Views	Jul 26, 2018 by dawsa925
A large lead angle on the cutting tool: A) Makes a chip thinner than the feed per tooth B) ... Started by D2AR0N	1 Replies 30 Views	Jul 26, 2018 by dpost18
Effective face milling requires: A) The right cutting speed B) A sharp cutting tool C) A rigid ... Started by Mimi	1 Replies 43 Views	Jul 26, 2018 by jennafosdick
Shell end mills: A) Cut surfaces square to the cutter axis B) Are arbor driven face mills C) Are ... Started by mcmcdaniel	1 Replies 41 Views	Jul 26, 2018 by pratush dev
Which of the following grinding wheel shapes permits grinding on both the face and the wall of the ... Started by s.tung	3 Replies 42 Views	Jul 26, 2018 by Viet Thy
The bond in most machine shop grinding wheels is: A) Rubber B) Vitrified C) Resinoid D) ... Started by cherise1989	1 Replies 20 Views	Jul 26, 2018 by kjo;oj
Grinding wheel dressing is done to: A) Prepare the wheel for form grinding B) Sharpen the ... Started by piesebel	1 Replies 35 Views	Jul 26, 2018 by brittrenee
The depth of infeed or downfeed per pass in truing should be no more than: A) .010 in. B) .001 ... Started by cagreen833	1 Replies 19 Views	Jul 26, 2018 by popopong
Grinding on the periphery of an abrasive wheel: A) Requires a harder wheel than for side grinding ... Started by AEWBW	3 Replies 79 Views	Jul 26, 2018 by elizabethrperez
The primary mark of a well designed fluid nozzle is that it: A) Is small in order to raise fluid ... Started by Evvie72	1 Replies 59 Views	Jul 26, 2018 by briezy
For maximum lubricating benefit, the fluid should be: A) Water-based soluble oil B) A stick ... Started by CQXA	1 Replies 39 Views	Jul 26, 2018 by komodo7