Skills and Trades

Replies / Views	Last post
What is the purpose of the footstock spring-loaded spindle? A) It keeps the lubricant in place ... Started by tth	1 Replies 423 Views	Jul 26, 2018 by zogaridan
What purpose is served by extending the table over travel beyond the workpiece dimensions? A) It ... Started by a0266361136	1 Replies 44 Views	Jul 26, 2018 by jojobee318
A superabrasive grinding wheel is glazed by truing. Conditioning is done using: A) Conditioning ... Started by bclement10	1 Replies 30 Views	Jul 26, 2018 by mochi09
When comparing crush dressing and plated diamond roll or block dressing, which of the following is ... Started by burchfield96	3 Replies 55 Views	Jul 26, 2018 by Tonny
If there is a lot of fluid flowing over the workpiece: A) It will keep the workpiece cool B) It ... Started by nramada	1 Replies 63 Views	Jul 26, 2018 by nhea
The saddle: A) Has a fixed relationship with the wheelhead B) Is fitted with a pommel for ... Started by pane00	1 Replies 12 Views	Jul 26, 2018 by helenmarkerine
What workpiece appearance discloses the need for increased grinding fluid filtration? A) Grinding ... Started by natalie2426	1 Replies 36 Views	Jul 26, 2018 by Harbringer
Face mills can generate: A) Irregular surfaces B) Surfaces parallel to the cutter axis C) ... Started by Collmarie	3 Replies 72 Views	Jul 26, 2018 by mbcrismon
A vise can be aligned by indicating the: A) Vise base B) Table C) Moveable jaw D) Solid ... Started by APUS57	1 Replies 100 Views	Jul 26, 2018 by tsternbergh47
Slots in workpieces should be measured: A) While they are warm B) Using a micrometer, adjustable ... Started by krzymel	1 Replies 39 Views	Jul 26, 2018 by cpetit11
In straddle milling, the width of the workpiece is controlled by the: A) Depth of cut B) Diameter ... Started by future617RT	1 Replies 56 Views	Jul 26, 2018 by bdobbins
Cutting fluids: A) Are coolants and lubricants B) Are used with high-speed steel cutters C) Can ... Started by sdfghj	3 Replies 59 Views	Jul 26, 2018 by jonathanballen97
Light duty face mills: A) Are used for roughing cuts B) Have many teeth C) Have few teeth D) ... Started by brutforce	1 Replies 20 Views	Jul 26, 2018 by upturnedfurball
When coolant is used, it will: A) Lengthen the life of the tool B) Shorten the life of the tool ... Started by Lobcity	1 Replies 23 Views	Jul 26, 2018 by nhea
T-slots in a machine table: A) Are used in conjunction with tee-nuts and clamp studs for ... Started by corkyiscool3328	1 Replies 13 Views	Jul 26, 2018 by hollysheppard095
A direct index plate with 24 holes is available. Which of the listed cannot be performed? A) 3 B) ... Started by wrbasek0	3 Replies 27 Views	Jul 26, 2018 by stanleka1
What is the feed rate for a 4-inch diameter cutter with 12 teeth, a feed rate of .010 inch and a CS ... Started by lindiwe	1 Replies 50 Views	Jul 26, 2018 by Mollythedog
A finished surface can be protected from clamping marks by: A) A piece of metal B) A thin piece ... Started by joesmith1212	1 Replies 71 Views	Jul 26, 2018 by fraziera112
Half side milling cutters are: A) Use to straddle mill B) Used to cut shallow grooves C) Used to ... Started by javeds	1 Replies 44 Views	Jul 26, 2018 by Ahernandez18
Trip dogs: A) Disengage power feeds B) Engage power feeds C) Extend the table travel D) All of ... Started by joblessjake	3 Replies 42 Views	Jul 26, 2018 by lcapri7
How many thousandths of an inch of material should be left for a finishing cut, when roughing out a ... Started by ts19998	3 Replies 32 Views	Jul 26, 2018 by momolu
The cutting edge of the boring tool: A) Can be at any angle to the axis of the tool slide B) ... Started by jenna1	1 Replies 40 Views	Jul 26, 2018 by braelync
Rapidly withdrawing a rotating boring bar immediately after the cut is completed, may: A) Cause ... Started by abern	1 Replies 16 Views	Jul 26, 2018 by vickybb89
When the depth of a cut in a boring operations increases, the: A) Surface finish will improve B) ... Started by bio_gurl	1 Replies 29 Views	Jul 26, 2018 by bbburns21
The spindle rotation is reversed: A) At slow spindle speeds B) At the end of each cut C) During ... Started by charchew	3 Replies 168 Views	Jul 26, 2018 by ebonylittles