Skills and Trades

Replies / Views	Last post
Which of these is NOT a sensor type used on an electronically controlled transmission? A) ... Started by kaid0807	3 Replies 143 Views	Jun 23, 2018 by diesoon
The proper term for Channel Locks is _________. A) Locking pliers B) Crescent wrench C) ... Started by @Brianna17	1 Replies 269 Views	Jun 23, 2018 by olderstudent
Which gas indicates efficiency? (The higher the level of this gas, the more efficient the engine is ... Started by 809779	1 Replies 119 Views	Jun 23, 2018 by upturnedfurball
An ignition fault could cause excessive ________ exhaust emissions. A) CO2 B) HC C) NOx D) ... Started by ishan	1 Replies 166 Views	Jun 23, 2018 by AISCAMPING
Where is the peen of the hammer? A) The striking face B) The part that connects to the handle C) ... Started by chandani	1 Replies 104 Views	Jun 23, 2018 by huda
Some states have a testing program that uses I/M 240 testing procedures. The number 240 refers to ... Started by Caiter2013	1 Replies 224 Views	Jun 23, 2018 by ms_sulzle
Which tool is most commonly used by automotive service technicians? A) Pliers B) Hammer C) Wrench ... Started by abern	1 Replies 176 Views	Jun 23, 2018 by nguyenhoanhat
Crowfoot sockets are available in which design? A) Flare nut wrench B) Open end wrench C) Both A ... Started by c0205847	1 Replies 132 Views	Jun 23, 2018 by uniquea123
Technician A says that a crowfoot socket can be used with a ratchet. Technician B says that a ... Started by EAugust	3 Replies 156 Views	Jun 23, 2018 by tjayeee
Technician A says that clicker type torque wrenches should be calibrated regularly. Technician B ... Started by TVarnum	1 Replies 276 Views	Jun 23, 2018 by aruss1303
Which type torque wrench displays the actual torque applied? A) Click B) Beam C) Both A and B D) ... Started by xclash	1 Replies 162 Views	Jun 23, 2018 by heyhey123
Technician A says that a 3 x 5 card should be held against the oil fill opening if the PCV system is ... Started by anjilletteb	1 Replies 88 Views	Jun 23, 2018 by meganmoser117
Technician A says that CO and HC levels should increase if the AIR hoses are pinched off. Technician ... Started by lb_gilbert	1 Replies 163 Views	Jun 23, 2018 by kilada
The stone wheel mounted to a bench grinder can be used for ________. A) Cleaning gaskets from ... Started by justinmsk	1 Replies 164 Views	Jun 23, 2018 by akudia
Using compressed air and an air gun, what is the maximum allowable air pressure? A) 20 psi B) 40 ... Started by Evvie72	1 Replies 116 Views	Jun 23, 2018 by AmberC1996
Technician A says that a defective TP sensor can cause the engine to hesitate during acceleration. ... Started by bobbie	1 Replies 152 Views	Jun 23, 2018 by 14vl19
Technician A says that defective spark plug wires can cause the engine to misfire. Technician B says ... Started by tth	3 Replies 428 Views	Jun 23, 2018 by meltdown117
Technician A says that poor fuel economy can be caused by a defective thermostat. Technician B says ... Started by NClaborn	1 Replies 311 Views	Jun 23, 2018 by mcarey591
Technician A says that the paper test could detect a burned valve. Technician B says that a grayish ... Started by asan beg	1 Replies 434 Views	Jun 23, 2018 by raenoj
Technician A says that a vacuum leak can cause a rough idle or stalling. Technician B says that ... Started by newbem	1 Replies 220 Views	Jun 23, 2018 by courtney_bruh
Technician A says that poor fuel economy is usually due to an excessively lean air-fuel mixture. ... Started by KimWrice	1 Replies 299 Views	Jun 23, 2018 by leeeep
Technician A says that a slowly cranking engine is usually caused by low battery voltage. Technician ... Started by penza	1 Replies 315 Views	Jun 23, 2018 by rosiehomeworddo
Technician A says that a leaking fuel pressure regulator diaphragm can cause run-on.Technician B ... Started by fasfsadfdsfa	1 Replies 170 Views	Jun 23, 2018 by mistyjohnson
Most air-operated grease guns operate with how much air pressure? A) 120 psi B) 30 psi C) 90 psi ... Started by viki	1 Replies 156 Views	Jun 23, 2018 by aham8f
When removing a bearing and race from a component _________. A) A bearing splitter may be needed ... Started by rosent76	3 Replies 313 Views	Jun 23, 2018 by ju