Skills and Trades

Replies / Views	Last post
Technician A says the flywheel is attached to the engine crankshaft and rotates at engine speed. ... Started by abc	1 Replies 327 Views	Aug 13, 2021 by lin77x
Technician A says a short input shaft needs a pilot bearing for support. Technician B says pilot ... Started by Brittanyd9008	1 Replies 166 Views	Aug 13, 2021 by Cheesycrackers
Most modern friction discs have cushion springs to ________. Started by bobypop	1 Replies 215 Views	Aug 13, 2021 by CourtneyCNorton
Modern clutch friction material is commonly made from ________. Started by evelyn o bentley	1 Replies 130 Views	Aug 13, 2021 by aloop
A manual transmission is difficult to shift or get into gear, especially reverse. Technician A says ... Started by eruditmonkey@yahoo.com	1 Replies 139 Views	Aug 13, 2021 by CharlieArnold
A growling noise is heard only when the driver exerts force on the clutch pedal. No noise is heard ... Started by brutforce	1 Replies 724 Views	Aug 13, 2021 by laurnthompson
A clutch is chattering when engaged. Technician A says that too much clutch freeplay is the cause. ... Started by jlmhmf	1 Replies 822 Views	Aug 13, 2021 by bigcheese9
Cross camber and cross caster should be within 1/2 degree from one side to the other. Started by TVarnum	1 Replies 149 Views	Aug 13, 2021 by otokexnaru
Which of these is NOT a part of a systematic diagnostic approach? Started by asmith134	1 Replies 74 Views	Aug 13, 2021 by cpetit11
Which angle is calculated as the wheels are turned from side to side? Started by formula1	1 Replies 139 Views	Aug 13, 2021 by carojassy25
What is the most common cause of memory steer? Started by Zulu123	1 Replies 44 Views	Aug 13, 2021 by ApricotDream
Use the following information to answer the question: Specifications:Min.PreferredMax.Camber ... Started by WWatsford	1 Replies 53 Views	Aug 13, 2021 by Kedrick2014
The proper order in which to perform a four-wheel alignment is ________. Started by MGLQZ	1 Replies 85 Views	Aug 13, 2021 by potomatos
Technician A says to inflate the tires to manufacturer's specifications before performing a wheel ... Started by soccerdreamer_17	1 Replies 40 Views	Aug 13, 2021 by ladyjames123
Technician A says that, as wear occurs, camber usually becomes negative. Technician B says that, as ... Started by yoooooman	1 Replies 91 Views	Aug 13, 2021 by kescobar@64
Technician A says that torque steer is normal on some FWD cars, especially during heavy ... Started by RODY.ELKHALIL	1 Replies 156 Views	Aug 13, 2021 by emsimon14
Technician A says that TOOT is the last adjustment made in a four wheel alignment. Technician B says ... Started by s.tung	1 Replies 202 Views	Aug 13, 2021 by bpool94
Technician A says that the alignment sensor heads only need to be compensated once per day. ... Started by Mr. Wonderful	1 Replies 124 Views	Aug 13, 2021 by ashely1112
Technician A says that dragging brakes are often discovered when mounting the alignment sensors on ... Started by nummyann	1 Replies 88 Views	Aug 13, 2021 by sabina576
Technician A says that a vehicle will pull (or lead) to the side with the most camber (or least ... Started by mp14	1 Replies 71 Views	Aug 13, 2021 by billybob123
Technician A says that a vehicle must have new tires in order to perform a proper alignment. ... Started by aabwk4	1 Replies 72 Views	Aug 13, 2021 by yasmin
Specifications:Min.PreferredMax.Camber (deg.)01.01.4Caster (deg.).81.52.1Toe ... Started by tichca	1 Replies 94 Views	Aug 13, 2021 by fdliggud
On a vehicle with electronically controlled suspension or stability control, what extra step may be ... Started by awywial	1 Replies 98 Views	Aug 13, 2021 by millet
If metal shims are used for alignment adjustment in the front, they adjust ________. Started by awywial	1 Replies 81 Views	Aug 13, 2021 by frogdreck123456
A vehicle will pull to the side with the most (positive) camber. Started by Melani1276	1 Replies 83 Views	Aug 13, 2021 by ApricotDream