Physics

Replies / Views	Last post
Note that the capacitors have different values.Refer to Figure 2. The circuit is a Started by ghost!	1 Replies 154 Views	Mar 20, 2019 by Zack0mack0101@yahoo.com
Note that the capacitors have different values.Refer to Figure 2. The fc for the first section is Started by Wadzanai	1 Replies 110 Views	Mar 20, 2019 by olderstudent
Stage 1: DF = 1.848 and R1/R2 = 0.152; stage 2: DF = 0.765 and R3/R4 =1.235.Refer to Figure ... Started by Deast7027	3 Replies 82 Views	Mar 20, 2019 by shewald78
Stage 1: DF = 1.848 and R1/R2 = 0.152; stage 2: DF = 0.765 and R3/R4 =1.235.Refer to Figure ... Started by Wadzanai	1 Replies 89 Views	Mar 20, 2019 by bassamabas
Stage 1: DF = 1.848 and R1/R2 = 0.152; stage 2: DF = 0.765 and R3/R4 =1.235.Refer to Figure ... Started by HCHenry	1 Replies 68 Views	Mar 20, 2019 by aburgess
Stage 1: DF = 1.848 and R1/R2 = 0.152; stage 2: DF = 0.765 and R3/R4 =1.235.Refer to Figure ... Started by soccerdreamer_17	3 Replies 65 Views	Mar 20, 2019 by Natalie4ever
A low-pass filter has a critical frequency of 10 kHz. The bandpass is Started by Redwolflake15	1 Replies 36 Views	Mar 20, 2019 by honnalora
The critical frequency of a high-pass filter is where the response is Started by AEWBW	3 Replies 50 Views	Mar 20, 2019 by reelove4eva
A basic one-pole RC low-pass filter has fc = 5.9 kHz using a 0.01 F capacitor. The resistor value is Started by crobinson2013	1 Replies 50 Views	Mar 20, 2019 by emsimon14
A biquad filter has both low-pass and high-pass outputs. Started by kwoodring	3 Replies 62 Views	Mar 20, 2019 by al
The Q of a band-pass filter is inversely proportional to the damping factor. Started by storky111	1 Replies 40 Views	Mar 20, 2019 by jesse.fleming
The damping factor, DF, is determined by the number of poles in a filter. Started by Deast7027	3 Replies 171 Views	Mar 20, 2019 by kjohnson
A single-pole filter cannot be used as a notch filter. Started by fagboi	1 Replies 69 Views	Mar 20, 2019 by nicoleclaire22
The damping factor, DF, affects an active filter's response characteristics. Started by justinmsk	3 Replies 44 Views	Mar 20, 2019 by kiamars2010
The Chebyshev filter is noted for its flat response in the passband. Started by roselinechinyere27m	1 Replies 34 Views	Mar 20, 2019 by annierak
The bandwidth of a basic band-pass filter is measured between the center frequency and a critical frequency. Started by Mr. Wonderful	3 Replies 68 Views	Mar 20, 2019 by frre432
A basic RC (one R, one C) filter has a 20dB/decade roll-off. Started by tiffannnnyyyyyy	1 Replies 47 Views	Mar 20, 2019 by fur
Refer to Figure 6(b). If the zener is open, the output current will be Started by rl	3 Replies 104 Views	Mar 20, 2019 by allisonblackmore
Refer to Figure 6(b). A shorted load, RL, is likely to cause Started by cmoore54	1 Replies 298 Views	Mar 20, 2019 by heyhey123
Refer to Figure 6(b). The current in RL is Started by burchfield96	3 Replies 31 Views	Mar 20, 2019 by milbourne11
Refer to Figure 6(b). The circuit is Started by geoffrey	1 Replies 83 Views	Mar 20, 2019 by emily12345
Refer to Figure 6(a). Assume S was momentarily closed and Vin is connected to a +3.0 VDC ... Started by jeatrice	3 Replies 54 Views	Mar 20, 2019 by brittanywood
Refer to Figure 6(a). The circuit is Started by lunatika	1 Replies 160 Views	Mar 20, 2019 by apple
With logarithmic signal compression, Started by kodithompson	3 Replies 68 Views	Mar 20, 2019 by ngr69
. The equation for the output is VOUT (0.025 V)1n Refer to Figure 5. To change this to an ... Started by nmorano1	1 Replies 79 Views	Mar 20, 2019 by aadams68