Physics

Replies / Views	Last post
Assume that +Vout(max) = +13 V and Vout(max) = 13 VRefer to Figure 1. The UTP is at Started by shofmannx20	3 Replies 88 Views	Mar 20, 2019 by k2629
The process of limiting the output of a comparator is called Started by rlane42	1 Replies 43 Views	Mar 20, 2019 by cassie_ragen
The purpose of a priority encoder in a flash ADC is to determine Started by cdr_15	3 Replies 68 Views	Mar 20, 2019 by mmj22343
Hysteresis avoids noise by using Started by Marty	1 Replies 25 Views	Mar 20, 2019 by mfedorka
The output of a differentiator represents the rate of change of the input. Started by Sufayan.ah	3 Replies 47 Views	Mar 20, 2019 by soda0602
An integrator circuit is useful in wave shaping applications. Started by 09madisonrousseau09	1 Replies 41 Views	Mar 20, 2019 by flexer1n1
An R/2R ladder is generally used as an ADC. Started by meagbuch	3 Replies 40 Views	Mar 20, 2019 by nixon_s
A practical integrator circuit often uses an inductor in the feedback path. Started by ARLKQ	1 Replies 37 Views	Mar 20, 2019 by dudman123
A differentiator circuit can output a square wave from a sine wave input. Started by waynest	3 Replies 116 Views	Mar 20, 2019 by connor417
A scaling amplifier is a summing amplifier with weighted inputs. Started by krzymel	1 Replies 50 Views	Mar 20, 2019 by succesfull
A flash ADC with a four-digit binary output requires 8 comparators. Started by jho37	3 Replies 89 Views	Mar 20, 2019 by yotaSR5
The output of a comparator is normally in one of two states. Started by stephzh	1 Replies 33 Views	Mar 20, 2019 by maaaaaaaaaa
Assume an op-amp has three different internal critical frequencies that are above the fT. The ... Started by elizabeth18	3 Replies 29 Views	Mar 20, 2019 by whitcassie
The RC components shown represent internal R and C of a compensated op-amp.Refer to Figure ... Started by EY67	1 Replies 36 Views	Mar 20, 2019 by xoxo123
The RC components shown represent internal R and C of a compensated op-amp.Refer to Figure ... Started by berenicecastro	3 Replies 73 Views	Mar 20, 2019 by trampas
Both op-amps are compensated and have AOL = 100 dB and fT = 2 MHz.Refer to Figure 4(b). If ... Started by Tazate	1 Replies 99 Views	Mar 20, 2019 by aloop
Both op-amps are compensated and have AOL = 100 dB and fT = 2 MHz.Refer to Figure 4(b). The ... Started by audie	3 Replies 58 Views	Mar 20, 2019 by Hikerman221
Both op-amps are compensated and have AOL = 100 dB and fT = 2 MHz.Refer to Figure 4(a). ... Started by Alygatorr01285	1 Replies 113 Views	Mar 20, 2019 by nyrave
Both op-amps are compensated and have AOL = 100 dB and fT = 2 MHz.Refer to Figure 4(a). The ... Started by Marty	1 Replies 80 Views	Mar 20, 2019 by chinwesucks
The need for bias current compensation is reduced by Started by Deast7027	3 Replies 36 Views	Mar 20, 2019 by carolinefletcherr
When the closed loop gain, ACL, is equal to 0 dB, the bandwidth is Started by Garrulous	1 Replies 110 Views	Mar 20, 2019 by kishoreddi
A typical op-amp Started by neverstopbelieb	3 Replies 27 Views	Mar 20, 2019 by FergA
Common-mode rejection ratio (CMRR) depends on the Started by vinney12	1 Replies 44 Views	Mar 20, 2019 by Edwyer
Refer to Figure 3. As the closed-loop gain, ACL, increases, the Started by chandani	3 Replies 157 Views	Mar 20, 2019 by Jossy
Refer to Figure 3. With a constant input, the output ranges from Started by joe	1 Replies 39 Views	Mar 20, 2019 by iceage