Picture Gallery

Search For: 

Others

Allows access to the nut that has a stud plus other locations needing great depth, such as spark ...
Views: 289
Filesize: 24.4kB
Date: May 25, 2017
 The most commonly used socket drive sizes include 1/4, 3/8, and 1/2 inch drives.
Views: 304
Filesize: 37.78kB
Date: May 25, 2017
 A typical ratchet used to rotate a socket. A ratchet makes a ratcheting noise when it is being ...
Views: 317
Filesize: 28.3kB
Date: May 25, 2017
 The end of a typical line wrench, which shows that it is capable of grasping most of the head of ...
Views: 329
Filesize: 342.17kB
Date: May 25, 2017
A combination wrench has an open end at one end and a box end at the other end.
Views: 263
Filesize: 37.42kB
Date: May 25, 2017
 The end of a box-end wrench is angled 15 degrees to allow clearance for nearby objects or other ...
Views: 270
Filesize: 29.56kB
Date: May 25, 2017
 A typical open-end wrench. Note the size difference on each end and that the head is angled 15 ...
Views: 381
Filesize: 33.71kB
Date: May 25, 2017
 A wrench after it has been forged but before the flashing (extra material around the wrench) has ...
Views: 278
Filesize: 1.01MB
Date: May 25, 2017
A rubber mallet used to deliver a force to an object without harming the surface.
Views: 331
Filesize: 369.69kB
Date: May 25, 2017
 A typical ball-peen hammer.
Views: 257
Filesize: 403.58kB
Date: May 25, 2017
 An offset screwdriver is used to install or remove fasteners that do not have enough space above to ...
Views: 299
Filesize: 155.87kB
Date: May 25, 2017
 Two stubby screwdrivers used to access screws that have limited space above. A straight blade is on ...
Views: 320
Filesize: 464.66kB
Date: May 25, 2017
A flat-tip (straight-blade) screwdriver. The width of the blade should match the width of the slot ...
Views: 346
Filesize: 29.52kB
Date: May 25, 2017
 Torque wrench calibration checker.
Views: 277
Filesize: 913.91kB
Date: May 25, 2017
 A beam-type torque wrench that displays the torque reading on the face of the dial. The beam display ...
Views: 371
Filesize: 1.02MB
Date: May 25, 2017
 Using a torque wrench to tighten connecting rod nuts on an engine.
Views: 277
Filesize: 1.72MB
Date: May 25, 2017
Allows access to the nut that has a stud plus other locations needing great depth, such as spark ...
Views: 301
Filesize: 24.4kB
Date: May 25, 2017
 A 6-point socket fits the head of a bolt or nut on all sides. A 12-point socket can round off the ...
Views: 343
Filesize: 67.42kB
Date: May 25, 2017
 The most commonly used socket drive sizes include 1/4, 3/8, and 1/2 inch drives.
Views: 324
Filesize: 37.78kB
Date: May 25, 2017
 A typical ratchet used to rotate a socket. A ratchet makes a ratcheting noise when it is being ...
Views: 340
Filesize: 28.3kB
Date: May 25, 2017
Pages: 1 ... 54 55 [56] 57 58 ... 120
Return to Gallery