Picture Gallery

Search For: 

Others

Diagnostic trouble codes (DTCs) from Chrysler and Dodge vehicles can be retrieved by turning the ...
Views: 434
Filesize: 2.02MB
Date: Jun 1, 2017
 To retrieve flash codes from an OBD-I General Motors vehicle, connect terminals A and B with the ...
Views: 410
Filesize: 10.19kB
Date: Jun 1, 2017
 A Bluetooth adapter that plugs into the DLC and transmits global OBD II information to a smart phone ...
Views: 450
Filesize: 1.33MB
Date: Jun 1, 2017
 A TECH 2 scan tool is the factory scan tool used on General Motors vehicles.
Views: 433
Filesize: 1.9MB
Date: Jun 1, 2017
Step 8 is very important. Be sure that the customer’s concern has been corrected.
Views: 463
Filesize: 114.88kB
Date: Jun 1, 2017
 Looking carefully at the scan tool data is very helpful in locating the source of a problem.
Views: 416
Filesize: 87.66kB
Date: Jun 1, 2017
 After checking for stored diagnostic trouble codes (DTCs), the wise technician checks service ...
Views: 386
Filesize: 1.42MB
Date: Jun 1, 2017
 Step 3 in the diagnostic process is to retrieve any stored diagnostic trouble codes.
Views: 442
Filesize: 134.58kB
Date: Jun 1, 2017
A spark tester connected to a spark plug wire or coil output. A typical spark tester will fire only ...
Views: 411
Filesize: 37.21kB
Date: Jun 1, 2017
 Using a bright light makes seeing where the smoke is coming from easier. In this case, smoke was ...
Views: 464
Filesize: 1.38MB
Date: Jun 1, 2017
 This is what was found when removing an air filter from a vehicle that had a lack-of-power concern. ...
Views: 392
Filesize: 1.28MB
Date: Jun 1, 2017
 A form that the customer should fill out if there is a driveablilty concern to help the service ...
Views: 397
Filesize: 329.37kB
Date: Jun 1, 2017
Step 1 is to verify the customer concern or problem. If the problem cannot be verified, then the ...
Views: 436
Filesize: 119.45kB
Date: Jun 1, 2017
 A funnel is one way to visualize the diagnostic process. The purpose is to narrow the possible ...
Views: 407
Filesize: 87.54kB
Date: Jun 1, 2017
 The fuel level must be above 15% and below 85% before the EVAP monitor will run on most vehicles.
Views: 393
Filesize: 1.39MB
Date: Jun 1, 2017
 This Toyota cap has a warning—the check engine light will come on if not tightened until one ...
Views: 393
Filesize: 1.71MB
Date: Jun 1, 2017
The fuel tank pressure sensor (black unit with three wires) looks like a MAP sensor and is usually ...
Views: 345
Filesize: 1.48MB
Date: Jun 1, 2017
 An emission tester that uses nitrogen to pressurize the fuel system.
Views: 311
Filesize: 2MB
Date: Jun 1, 2017
 This unit is applying smoke to the fuel tank through an adapter and the leak was easily found to be ...
Views: 393
Filesize: 1.62MB
Date: Jun 1, 2017
 To test for a leak, this tester was set to the 0.020 inch hole and turned on. The ball rose in the ...
Views: 367
Filesize: 962.5kB
Date: Jun 1, 2017
Pages: 1 ... 18 19 [20] 21 22 ... 120
Return to Gallery