Skills and Trades

Replies / Views	Last post
The pushrod length should be checked whenever a new master cylinder is installed. Indicate ... Started by 123654777	1 Replies 109 Views	Jun 23, 2018 by TheNamesImani
Technician A says that most ABS units are non-integral.. Technician B says that the ABS is disabled ... Started by ec501234	1 Replies 182 Views	Jun 23, 2018 by owenfalvey
Technician A says that the parking brake cable adjustment should be performed before adjusting the ... Started by deesands	1 Replies 155 Views	Jun 23, 2018 by catron30
The static friction coefficient is always higher than the kinetic friction coefficient. Indicate ... Started by yoroshambo	1 Replies 243 Views	Jun 23, 2018 by wuly
Self apply of the brakes can occur if ________. A) The vent port is clogged or covered B) The ... Started by @Brianna17	3 Replies 229 Views	Jun 23, 2018 by Dominic
Technician A says that brake pedal freeplay may be as little as 1/8 inch. Technician B says that ... Started by Jkov05	1 Replies 215 Views	Jun 23, 2018 by kxciann
What part is often NOT used on a front-wheel drive vehicle with a manual transaxle? A) Clutch ... Started by colton	1 Replies 137 Views	Jun 23, 2018 by meltdown117
To save time, technician A uses an impact socket on an impact wrench to tighten lug nuts. Technician ... Started by deesands	1 Replies 229 Views	Jun 23, 2018 by Jossy
Which type of fluid is typically used in a hydraulic clutch system? A) Engine oil B) Automatic ... Started by ssal	1 Replies 115 Views	Jun 23, 2018 by wtf444
Before removing the transmission make sure the battery is charged and connected in order to retain ... Started by xclash	1 Replies 169 Views	Jun 23, 2018 by kaillie
Technician A says that snap rings are used to hold many components of a manual ... Started by Mimi	1 Replies 146 Views	Jun 23, 2018 by T4T
A four-speed transmission is making a grinding noise only while shifting into second gear. This ... Started by Alygatorr01285	1 Replies 96 Views	Jun 23, 2018 by mcomstock09
Technician A says that the engine drives the U-joint at a constant speed, but the output speed of ... Started by imowrer	3 Replies 168 Views	Jun 23, 2018 by annierak
FWD driveshaft problems are usually indicated by ________. A) Noise B) Grease from a torn boot ... Started by Anajune7	1 Replies 217 Views	Jun 23, 2018 by stillxalice
The spacer used on a drive pinion gear is used to properly position the gear so that it can ... Started by Chloeellawright	1 Replies 320 Views	Jun 23, 2018 by lkanara2
The backlash is less than specifications (too low). This will cause the ring gear tooth pattern to ... Started by nummyann	1 Replies 198 Views	Jun 23, 2018 by shayla
Ring gear runout should be less than ________ as measured by a dial indicator. A) 1/10th of an ... Started by michelleunicorn	1 Replies 128 Views	Jun 23, 2018 by steff9894
The firm setting is usually selected by the electronic suspension control module whenever which of ... Started by Davideckstein7	1 Replies 349 Views	Jun 23, 2018 by Sammyo
Technician A says that some GM vehicles have only one height sensor. Technician B says that GM ... Started by sabina	1 Replies 140 Views	Jun 23, 2018 by ryrychapman11
Two technicians are discussing the front axle disconnect mechanism. Technician A says that the front ... Started by sarasara	1 Replies 222 Views	Jun 23, 2018 by abctaiwan
Technician A says the torque multiplication phase can occur when the stator one-way clutch begins to ... Started by lak	3 Replies 176 Views	Jun 23, 2018 by anyusername12131
One clutch in a dual clutch transmission is used for 1st, 2nd, and 3rd gears. Indicate whether ... Started by CQXA	1 Replies 180 Views	Jun 23, 2018 by frejo
Technician A says that a held member is also called the reaction member. Technician B says that if ... Started by elizabeth18	1 Replies 239 Views	Jun 23, 2018 by sabina576
What is the purpose and function of an accumulator? A) To apply a band B) To apply a clutch C) ... Started by Engineer	1 Replies 130 Views	Jun 23, 2018 by bookworm410
Technician A says shift solenoids are used on some transmissions to control upshifts and downshifts. ... Started by ssal	1 Replies 252 Views	Jun 23, 2018 by carlsona147