Skills and Trades

Replies / Views	Last post
The major reason for brake pedal pulsation during braking is due to excessive rotor thickness variation. Started by CQXA	1 Replies 91 Views	Aug 13, 2021 by otokexnaru
Which one is not a form of drum distortion? Started by gbarreiro	1 Replies 175 Views	Aug 13, 2021 by ilianabrrr
Typical maximum rotor thickness variation (parallelism) specifications are ________. Started by kamilo84	1 Replies 151 Views	Aug 13, 2021 by nanny
Two technicians are discussing the machining of brake drums. Technician A says that most brake drums ... Started by Alygatorr01285	1 Replies 141 Views	Aug 13, 2021 by mjbamaung
Two technicians are discussing hard spots in brake drums. Technician A says the drum should be ... Started by frankwu	1 Replies 114 Views	Aug 13, 2021 by ryansturges
Two technicians are discussing disc brake rotor service. Technician A says that the inner races ... Started by azncindy619	1 Replies 88 Views	Aug 13, 2021 by Kaytorgator
The lower the Ra of a rotor, the ________ the surface. Started by ssal	1 Replies 111 Views	Aug 13, 2021 by kaillie
Technician A says there are no brake lathes that can machine rotors on the vehicle. Technician B ... Started by mcmcdaniel	1 Replies 131 Views	Aug 13, 2021 by ttt030911
Technician A says that hard spots in a brake drum should be removed using a carbide-tip machining ... Started by shofmannx20	1 Replies 90 Views	Aug 13, 2021 by gabrielle_lawrence
Technician A says that brake drums on the same axle should be close to the same inside diameter for ... Started by Mr3Hunna	1 Replies 86 Views	Aug 13, 2021 by carolinefletcherr
Technician A says that aluminum brake drums use cast iron friction surfaces. Technician B says that ... Started by jake	1 Replies 102 Views	Aug 13, 2021 by Jmfn03
Technician A says heat checking can be caused by numerous panic stops in rapid succession. ... Started by mp14	1 Replies 61 Views	Aug 13, 2021 by leahm14
Technician A says anti-vibration devices only need to be used when resurfacing drums. Technician B ... Started by tingc95	1 Replies 113 Views	Aug 13, 2021 by bblaney
Most manufacturers specify that the friction surfaces of a rotor must be parallel to within ________. Started by leilurhhh	1 Replies 71 Views	Aug 13, 2021 by pami445
The parking brake warning light is independent of all other systems. Started by hubes95	1 Replies 115 Views	Aug 13, 2021 by macmac
Federal regulations require the parking brake to hold the vehicle in position on a 20 percent grade. Started by waynest	1 Replies 67 Views	Aug 13, 2021 by soda0602
Two technicians are discussing parking brake systems that mechanically actuate the rear disc brakes. ... Started by jho37	1 Replies 145 Views	Aug 13, 2021 by kardosa007
The rear brakes should be inspected, and adjusted if necessary, if the parking brake requires more ... Started by Tirant22	1 Replies 113 Views	Aug 13, 2021 by samiel-sayed
Technician A says that the parking brake is controlled by a lever. Technician B says that a pedal ... Started by scienceeasy	1 Replies 83 Views	Aug 13, 2021 by shoemake
Technician A says that the parking brake hand lever can turn on the red brake warning lamp. ... Started by Melani1276	1 Replies 137 Views	Aug 13, 2021 by Ddddd
Technician A says that the parking brake cable should be adjusted at each wheel. Technician B says ... Started by laurencescou	1 Replies 104 Views	Aug 13, 2021 by abro1885
Technician A says that the parking brake cable adjustment should be performed before adjusting the ... Started by abc	1 Replies 110 Views	Aug 13, 2021 by ndhahbi
Technician A says that if the parking brake cable is adjusted too tight, the rear brakes may drag ... Started by vinney12	1 Replies 140 Views	Aug 13, 2021 by mcarey591
Technician A says that an electric parking brake (EPB) uses an electric motor to pull on the parking ... Started by jilianpiloj	1 Replies 129 Views	Aug 13, 2021 by Bigfoot1984
Technician A says that a vehicle can fail a parking brake performance test if the linings are ... Started by stevenposner	1 Replies 84 Views	Aug 13, 2021 by Liddy