Skills and Trades

Replies / Views	Last post
When wheel bearings are adjusted with a dial indicator, allow .005" to .010" (.127 to .25 mm) of end play. Started by saliriagwu	1 Replies 100 Views	Aug 13, 2021 by gstein359
Bearings cannot be diagnosed by turning the wheel and tire assembly by hand. Started by jCorn1234	1 Replies 143 Views	Aug 13, 2021 by InfiniteSteez
Which type of automotive bearing can withstand radial and thrust loads, yet must be adjusted for ... Started by Zoey63294	1 Replies 125 Views	Aug 13, 2021 by britb2u
When road testing a vehicle with adjustable dual wheel bearings, a swerve to the right causes noise. ... Started by cookcarl	1 Replies 88 Views	Aug 13, 2021 by juliaf
Wheel bearings are being packed with grease. Technician A says to use grease that is labeled "GC." ... Started by eruditmonkey@yahoo.com	1 Replies 114 Views	Aug 13, 2021 by Gabe
Two technicians are discussing wheel bearings. Technician A says that conventional tapered roller ... Started by dejastew	1 Replies 105 Views	Aug 13, 2021 by akpaschal
Two technicians are discussing differentials. Technician A says that all differentials are vented. ... Started by OSWALD	1 Replies 89 Views	Aug 13, 2021 by macagn
The differential cover must be removed before removing the rear axle on which type of axle? Started by notis	1 Replies 152 Views	Aug 13, 2021 by kingfahad97
Technician A says that excessive axial end play is a sign that wheel bearings need service. ... Started by lunatika	1 Replies 80 Views	Aug 13, 2021 by okolip
Technician A says that a defective wheel or axle bearing often makes a growling or rumbling noise. ... Started by nummyann	1 Replies 178 Views	Aug 13, 2021 by kristenb95
Technician A says a poor engine ground connection can cause electricity to flow through wheel ... Started by Jramos095	1 Replies 91 Views	Aug 13, 2021 by verrinzo
On a bearing that has been shock loaded, the race (cup) of the bearing can be dented. This type of ... Started by 2125004343	1 Replies 87 Views	Aug 13, 2021 by kilada
Most sealed bearings used on the front wheels of front-wheel-drive vehicles are usually which type? Started by justinmsk	1 Replies 136 Views	Aug 13, 2021 by DylanD1323
A non-drive-wheel bearing adjustment procedure includes a final spindle nut tightening torque of ________. Started by melina_rosy	1 Replies 167 Views	Aug 13, 2021 by rosiehomeworddo
When bleeding wheel brakes, the bleeder screw is usually loosened one-half turn. Started by jwb375	1 Replies 130 Views	Aug 13, 2021 by xMRAZ
Discharge the power brake booster before manually bleeding the brakes. Started by saraeharris	1 Replies 73 Views	Aug 13, 2021 by joneynes
Why shouldn't a service technician depress a brake pedal all the way down when bleeding brakes? Started by mspears3	1 Replies 76 Views	Aug 13, 2021 by jgranad15
While bleeding brakes, how long should you wait between strokes? Started by natalie2426	1 Replies 215 Views	Aug 13, 2021 by Li Jun
Vacuum is applied where during vacuum bleeding? Started by darbym82	1 Replies 139 Views	Aug 13, 2021 by jomama
Two technicians are discussing how to loosen bleeder valves. Technician A says that a shock is ... Started by Pineappleeh	1 Replies 110 Views	Aug 13, 2021 by nanny
Two technicians are discussing bleeding air from the brake hydraulic system. Technician A says to ... Started by Kikoku	1 Replies 144 Views	Aug 13, 2021 by dajones82
Two technicians are discussing bench bleeding a master cylinder. Technician A says that the front ... Started by vicky	1 Replies 103 Views	Aug 13, 2021 by 1_Step_At_ATime
The button on the ________ valve should be held when pressure bleeding the brakes. Started by jhjkgdfhk	1 Replies 147 Views	Aug 13, 2021 by joshraies
The bleeder is opened at a caliper and no brake fluid flows out. Technician A says that this is ... Started by Jkov05	1 Replies 125 Views	Aug 13, 2021 by 14vl19
Technician A says to bleed the conventional brake system before bleeding the ABS modulator. ... Started by humphriesbr@me.com	1 Replies 44 Views	Aug 13, 2021 by katieost