Skills and Trades

Replies / Views	Last post
Electricity moving through a conductor produces a magnetic field. This principle is used in which of ... Started by mmm	1 Replies 130 Views	Aug 13, 2021 by rachel
Creating electricity by exerting force on a crystal is called ________. Started by hubes95	1 Replies 64 Views	Aug 13, 2021 by blakcmamba
As temperature increases, ________. Started by daltonest1984	1 Replies 49 Views	Aug 13, 2021 by briseldagonzales
A rheostat usually has how many wires? Started by Beheh	1 Replies 56 Views	Aug 13, 2021 by asdfghjkl;
A potentiometer usually has how many wires? Started by Arii_bell	1 Replies 64 Views	Aug 13, 2021 by juicepod
Two technicians are discussing the installation of a rebuilt engine into a vehicle. Technician A ... Started by hbsimmons88	1 Replies 119 Views	Aug 13, 2021 by voltaire123
Technician A says to use SAE 30 engine oil on an engine break-in. Technician B says that it is ... Started by leo leo	1 Replies 295 Views	Aug 13, 2021 by fraziera112
Technician A says to always adjust the clutch free play after starting the engine. Technician B says ... Started by Zoey63294	1 Replies 106 Views	Aug 13, 2021 by succesfull
Lugging an engine means ________. Started by c0205847	1 Replies 146 Views	Aug 13, 2021 by Jane
If the bell housing is not properly torqued to the engine block, ________. Started by mrsjacobs44	1 Replies 83 Views	Aug 13, 2021 by stallen
Engine vacuum on a normal stock rebuilt engine should be ________ Started by arivle123	1 Replies 154 Views	Aug 13, 2021 by stillxalice
What would happen if oil or water (coolant) was at the bottom of a dry hole in the bolt when the ... Started by magmichele12	1 Replies 135 Views	Aug 13, 2021 by onowka
What can be used to check that the heads are at the correct angle for the intake manifold on a V-type engine? Started by waynest	1 Replies 85 Views	Aug 13, 2021 by Jmfn03
Two technicians are discussing the torqueing procedure for head bolts. Technician A says that they ... Started by Starlight	1 Replies 130 Views	Aug 13, 2021 by huda
The TTY method of tightening bolts involves which of these processes? Started by captainjonesify	1 Replies 96 Views	Aug 13, 2021 by huda
Technician A says that the torque applied to the head bolts is the same as the clamping force on the ... Started by Chloeellawright	1 Replies 76 Views	Aug 13, 2021 by nguyenhoanhat
Technician A says that the cam bearings should be installed using a driver and dead blow hammer. ... Started by jman1234	1 Replies 86 Views	Aug 13, 2021 by chreslie
Technician A says that the back of all engine bearings should be lubricated during assembly. ... Started by Tirant22	1 Replies 103 Views	Aug 13, 2021 by bbburns21
Technician A says that studs should be installed finger tight. Technician B says that studs must be ... Started by crazycityslicker	1 Replies 556 Views	Aug 13, 2021 by adammoses97
Technician A says that glues are used to help gaskets seal. Technician B says that deburring all ... Started by yoroshambo	1 Replies 1,065 Views	Aug 13, 2021 by ryansturges
Technician A says that all oil galleries must be thoroughly cleaned before engine assembly can ... Started by mrsjacobs44	1 Replies 185 Views	Aug 13, 2021 by kalskdjl1212
Service information states SAE 30 engine oil should be used on the threads of the head bolts, before ... Started by anjilletteb	1 Replies 158 Views	Aug 13, 2021 by voltaire123
Main bearings and rod bearings should be checked for proper oil clearance by precision measuring the ... Started by ENagel	1 Replies 98 Views	Aug 13, 2021 by samiel-sayed
Head gasket installation is being discussed. Technician A says that the surface finish of the ... Started by dollx	1 Replies 83 Views	Aug 13, 2021 by ryrychapman11
Engine pre-oiling is recommended for which of these reasons? Started by daltonest1984	1 Replies 43 Views	Aug 13, 2021 by scrocafella