Skills and Trades

Replies / Views	Last post
Technician A says that containers for dirty shop rags should be made of metal. Technician B says ... Started by Bob-Dole	1 Replies 145 Views	Jun 23, 2018 by britb2u
Aisles should be marked with _______. A) Duck tape B) Yellow paint C) Black tape D) Duct ... Started by WWatsford	3 Replies 189 Views	Jun 23, 2018 by welcom1000
Which type of cleaning uses small living organisms to eat oil and grease? A) Solvent B) Microbe ... Started by tatyanajohnson	1 Replies 163 Views	Jun 23, 2018 by asdfghjkl;
The throttle position sensor used in the throttle body assembly of an electronic throttle control ... Started by leo leo	1 Replies 170 Views	Jun 23, 2018 by princessflame2016
Batteries should not be tipped to more than a ________ angle. A) 60 degree B) 5 degree C) 45 ... Started by evelyn o bentley	1 Replies 320 Views	Jun 23, 2018 by Toya9913
Technician A says that an eyewash station should be located in the corner of the shop to keep it ... Started by joe	1 Replies 144 Views	Jun 23, 2018 by bhavsar
Evacuation route maps are usually located ________. A) In the men's room B) On the floor C) Near ... Started by SO00	1 Replies 90 Views	Jun 23, 2018 by Sammyo
Hazardous materials include all of the following EXCEPT _________. A) Engine oil B) Brake cleaner ... Started by cagreen833	1 Replies 184 Views	Jun 23, 2018 by kusterl
A throttle body relearn procedure uses ________ to relearn proper idle speed. A) A vacuum gauge ... Started by OSWALD	1 Replies 220 Views	Jun 23, 2018 by jazzlynnnnn
Which law states that users of hazardous wastes are legally responsible for the materials from the ... Started by tsand2	3 Replies 123 Views	Jun 23, 2018 by bulacsom
All the criteria below are used by the EPA to determine if a substance can be called used oil, ... Started by dmcintosh	1 Replies 104 Views	Jun 23, 2018 by kescobar@64
Which statement below regarding airborne asbestos is correct? A) Large and small asbestos ... Started by karateprodigy	1 Replies 127 Views	Jun 23, 2018 by kingdude89
Technician A says that lead-acid batteries may be disposed of in landfills. Technician B says that ... Started by michelleunicorn	1 Replies 161 Views	Jun 23, 2018 by blfontai
What does the electronic pressure control (EPC) solenoid use to control mainline pressure? A) ... Started by kamilo84	1 Replies 157 Views	Jun 23, 2018 by nekcihc358
OSHA standards are designed to limit damage to vehicles. Indicate whether the statement is true ... Started by jeatrice	1 Replies 111 Views	Jun 23, 2018 by Zack0mack0101@yahoo.com
The controlling unit for an electronically shifted transmission is the ________. A) TCM B) ... Started by javeds	1 Replies 257 Views	Jun 23, 2018 by jesse.fleming
Metric thread pitch is measured in _________. A) Millimeters B) Inches C) Centimeters D) None of ... Started by sarasara	1 Replies 217 Views	Jun 23, 2018 by jaygar71
The output speed sensor is also called a ________. A) Turbine speed sensor (TSS) B) Output speed ... Started by Capo	3 Replies 203 Views	Jun 23, 2018 by SomethingSomething
A bolt that is threaded into a casting is often called a _________. A) Crest bolt B) Cap screw C) ... Started by SO00	1 Replies 151 Views	Jun 23, 2018 by HandsomeMarc
If the solenoids fail in a transmission with electronic shift controls, the transmission will ... Started by scienceeasy	1 Replies 106 Views	Jun 23, 2018 by Ksh22
The number of threads per inch is referred to as _________. A) Grade B) Gauge C) Pitch D) None of ... Started by cagreen833	1 Replies 127 Views	Jun 23, 2018 by aloop
Which of these is used to cut threads in a drilled hole? A) Tap B) Die C) Either A or B D) ... Started by maychende	1 Replies 134 Views	Jun 23, 2018 by poopface
Which type of washer is used to provide an even clamping force? A) Lock washer B) Flat washer C) ... Started by wrbasek0	1 Replies 199 Views	Jun 23, 2018 by Tabitha_2016
Which of these may be used to restore damaged threads on a bolt? A) Tap B) Die C) Either A or B ... Started by tingc95	1 Replies 81 Views	Jun 23, 2018 by FergA
The most commonly used tap is a _________. A) Bottoming tap B) Tapered tap C) Both A and B D) ... Started by olgavictoria	1 Replies 86 Views	Jun 23, 2018 by Animal_Goddess