This topic contains a solution. Click here to go to the answer
« previous next »

Author Question: On a CNC vertical spindle machining center, a Z axis offset is: A) The distance from the tool tip ... (Read 40 times)

809779

  • Hero Member
  • *****
  • Posts: 579
on: Jul 26, 2018
On a CNC vertical spindle machining center, a Z axis offset is:
 
  A) The distance from the tool tip to the work top surface in the X axis
  B) The distance from the tool tip to the work top surface in the Z axis
  C) The distance of the spindle to the Y axis
  D) The distance from the machine to the shop wall

Question 2

G92 sets:
 
  A) Turning mode B) Milling mode
  C) Workpiece coordinates at program start D) Metric dimensioning mode


Related Topics

Need homework help now?

Ask unlimited questions for free

Ask a Question
Marked as best answer by a Subject Expert

Athena23

  • Sr. Member
  • ****
  • Posts: 305
Reply #1 on: Jul 26, 2018
Answer to Question 1

B

Answer to Question 2

C


809779

  • Hero Member
  • *****
  • Posts: 579
Reply #2 on: Jul 26, 2018
TY


Athena23

  • Sr. Member
  • ****
  • Posts: 305
Reply #3 on: Jul 26, 2018
You're welcome


« previous next »
 

Did you know?

When Gabriel Fahrenheit invented the first mercury thermometer, he called "zero degrees" the lowest temperature he was able to attain with a mixture of ice and salt. For the upper point of his scale, he used 96°, which he measured as normal human body temperature (we know it to be 98.6° today because of more accurate thermometers).

Did you know?

Many people have small pouches in their colons that bulge outward through weak spots. Each pouch is called a diverticulum. About 10% of Americans older than age 40 years have diverticulosis, which, when the pouches become infected or inflamed, is called diverticulitis. The main cause of diverticular disease is a low-fiber diet.

Did you know?

Fewer than 10% of babies are born on their exact due dates, 50% are born within 1 week of the due date, and 90% are born within 2 weeks of the date.

Did you know?

Asthma attacks and symptoms usually get started by specific triggers (such as viruses, allergies, gases, and air particles). You should talk to your doctor about these triggers and find ways to avoid or get rid of them.

Did you know?

Although the Roman numeral for the number 4 has always been taught to have been "IV," according to historians, the ancient Romans probably used "IIII" most of the time. This is partially backed up by the fact that early grandfather clocks displayed IIII for the number 4 instead of IV. Early clockmakers apparently thought that the IIII balanced out the VIII (used for the number 8) on the clock face and that it just looked better.

Global view of Mars as seen by the Viking 1 orbiter in 1980, showing the Valles Marineris (center) Global view of Mars as seen by the Viking 1 orbiter in 1980, showing the Valles Marineris (center)
Transverse Breaks the shaft of a bone across its longitudinal axis; the break is in the fibula, the Transverse Breaks the shaft of a bone across its longitudinal axis; the break is in the fibula, the
Major trunk lines carrying long-distance traffic crisscrossed the area east of the Mississippi. The Major trunk lines carrying long-distance traffic crisscrossed the area east of the Mississippi. The
In Chuck Close's portrait, the face is quite recognizable when viewed from a distance. Close ... In Chuck Close's portrait, the face is quite recognizable when viewed from a distance. Close ...
A fuel composition tester (SPX Kent-Moore J-44175) is the recommended tool, by General Motors, to ... A fuel composition tester (SPX Kent-Moore J-44175) is the recommended tool, by General Motors, to ...
A spark plug thread chaser is a low-cost tool that hopefully will not be used often, but is ... A spark plug thread chaser is a low-cost tool that hopefully will not be used often, but is ...
Video: Introduction to Sickle Cell Anemia

For a complete list of videos, visit our video library