This topic contains a solution. Click here to go to the answer
« previous next »

Author Question: List three considerations that must be taken into account in the placement, number and size of the ... (Read 48 times)

SGallaher96

  • Hero Member
  • *****
  • Posts: 509
on: Aug 19, 2018
List three considerations that must be taken into account in the placement, number and size of the vent holes in a female mold used for fundamental (straight) vacuum forming.
 
  What will be an ideal response?

Question 2

Discuss the pressure capabilities of vacuum forming relative to pressure forming.
 
  What will be an ideal response?


Related Topics

Need homework help now?

Ask unlimited questions for free

Ask a Question
Marked as best answer by a Subject Expert

ghepp

  • Sr. Member
  • ****
  • Posts: 361
Reply #1 on: Aug 19, 2018
Answer to Question 1

The holes should be as large as possible to allow fast application of the vacuum without showing through onto the surface of the plastic. Soft plastics or those that are heated to high temperatures will probably require smaller holes. The holes should be placed as far apart as is practical while assuring that all areas of the plastic sheet are drawn tightly against the cavity walls. Holes should be placed in any corner or other area where webbing or bridging might be a problem.

Answer to Question 2

With vacuum forming the maximum pressure available is the difference between the pressure in the evacuated chamber and atmospheric pressure. Hence, the pressure is limited to a max of one atmosphere. With pressure forming any pressure can be applied, although normally very high pressures are not needed. The pressures used in pressure forming, however, would always be higher than those used in vacuum forming.


SGallaher96

  • Member
  • Posts: 509
Reply 2 on: Aug 19, 2018
Wow, this really help

JaynaD87

  • Member
  • Posts: 368
Reply 3 on: Yesterday
:D TYSM

« previous next »
 

Did you know?

Asthma attacks and symptoms usually get started by specific triggers (such as viruses, allergies, gases, and air particles). You should talk to your doctor about these triggers and find ways to avoid or get rid of them.

Did you know?

The most dangerous mercury compound, dimethyl mercury, is so toxic that even a few microliters spilled on the skin can cause death. Mercury has been shown to accumulate in higher amounts in the following types of fish than other types: swordfish, shark, mackerel, tilefish, crab, and tuna.

Did you know?

People with alcoholism are at a much greater risk of malnutrition than are other people and usually exhibit low levels of most vitamins (especially folic acid). This is because alcohol often takes the place of 50% of their daily intake of calories, with little nutritional value contained in it.

Did you know?

The most common treatment options for addiction include psychotherapy, support groups, and individual counseling.

Did you know?

Adolescents often feel clumsy during puberty because during this time of development, their hands and feet grow faster than their arms and legs do. The body is therefore out of proportion. One out of five adolescents actually experiences growing pains during this period.

Isotopes may be stable or radioactive depending on the arrangement and number of neutrons in the nuc Isotopes may be stable or radioactive depending on the arrangement and number of neutrons in the nuc
When the number of miles traveled is considered, drivers under 25 years of age and those over 70 are ... When the number of miles traveled is considered, drivers under 25 years of age and those over 70 are ...
Annual Mean Number of Days with Thunder Annual Mean Number of Days with Thunder
Average Number of Days per Year with Thunderstorms Average Number of Days per Year with Thunderstorms
A thimble of water contains 4.0 x 1021 molecules. The number of moles of H2O is: A thimble of water contains 4.0 x 1021 molecules. The number of moles of H2O is:
Number writing practice 1-30 kindergarten Number writing practice 1-30 kindergarten
Video: Spermatogenesis Animation

For a complete list of videos, visit our video library